Inconel 718 is an age-hardenable Alloy-chromium alloy that combines corrosion resistance with high strength and good fabricability. It has high creep-rupture strength at temperatures up to 700 ℃. Its excellent relaxation resistance contributes to its application in springs
904L stainless steel is a non-stabilized austenitic stainless steel with low carbon content. This high alloy stainless steel is added with copper to improve its resistance to strong reducing acids, such as sulphuric acid. The steel is also resistant to stress corrosion cracking and crevice corrosion
Inconel is a nickel-chromium-based superalloy often utilized in extreme environments where components are subjected to high temperature, pressure or mechanical loads. Inconel alloys are oxidation- and corrosion-resistant. When heated, Inconel forms a thick, stable, passivating oxide layer protecting the surface from further attack
The Inconel 690 material is a kind of austenitic nickel-base superalloy, which has excellent stress corrosion cracking resistance, excellent corrosion resistance, high strength, strong antioxidation, and favorable metallurgy stability
Grade 316 stainless steel plate is the standard molybdenum-bearing grade of stainless steel plate. The molybdenum gives 316 stainless steel plate better overall corrosion resistant properties than grade 304 stainless steel plate. It has particularly higher resistance to pitting and crevice corrosion in chloride environments. 316 stainless steel plate has excellent forming and welding characteristics. It is readily brake or roll formed into a variety of parts for applications in the industrial, architectural, and transportation fields. Grade 316 stainless steel plate also has outstanding welding characteristics. Grade 316L stainless steel plate is the low carbon version of 316 stainless steel plate and is extensively used in heavy gauge welded components.
The Inconel 690 material is a kind of austenitic nickel-base superalloy, which has excellent stress corrosion cracking resistance, excellent corrosion resistance, high strength, strong antioxidation, and favorable metallurgy stability
Inconel 600 is combination of Nickel Chromium and Iron providing a standard material for the chemical industry and the automotive engine, aero engine and airframe sectors
7075 aluminium alloy (AA7075) is an aluminium alloy with zinc as the primary alloying element. It has excellent mechanical properties and exhibits good ductility, high strength, toughness, and good resistance to fatigue. It is more susceptible to embrittlement than many other aluminium alloys because of microsegregation, but has significantly better corrosion resistance than the alloys from the 2000 series. It is one of the most commonly used aluminium alloys for highly stressed structural applications and has been extensively used in aircraft structural parts.
A duplex is generally a property divided into two separate living units. Those units can be situated side by side or stacked one on top of the other (the “one-up, one-down”). There are separate entrances for each unit, and sometimes there are separate garages and yards, as well
254 SMO Plate is a type of austenitic steel. Austenitic steel is a type of stainless steel which contains low amounts of carbon only up to 0.8% in weight. SMO 254 Plate is a very high end stainless steel that it has the mechanical properties with values almost twice the values of the 300 series steels in most cases
Stainless steel is a corrosion-resistant alloy of iron, chromium and, in some cases, nickel and other metals. Completely and infinitely recyclable, stainless steel is the “green material” par excellence. In fact, within the construction sector, its actual recovery rate is close to 100%.
Duplex SS are two-phase alloys containing equal proportion of ferritic and austenitic phases in their microstructure, providing a combination of the corrosion resistance of austenitic stainless steels with greater strength
Ferralium 255 is a super duplex stainless steel in the Ferralium family. It was the first super duplex stainless steel. Developed by Langley Alloys to meet the needs of the oil, gas and chemical industries, Ferralium 255 achieves higher strengths than most other stainless steel varieties and corrosion-resistant alloys
Steel Plate, or structural steel is simply steel sheet material that can be customarily cut and welded to develop a more elaborate product. It is made by compressing multiple steel layers together into one; forming a plate of steel.
Steel Plate is commonly used to strengthen foundations and uphold mass units of weight like bridges. Alternatively, it provides a base for construction of larger materials and non-workable parts.
Applications for Steel Plate are based acutely on the specifics of the project. This simply means that certain grades are more appropriate to particular tasks than others.
Request Callback
Yes! I am Interested
410 Stainless Steel Plate
Get Best Quote
Approx. Price: Rs 150 / KgGet Latest Price
Product Details:
Surface Treatment
Hot Rolled
Shape
Rectangular
Brand
Milton Steel
Color
Silver
Material
Stainless Steel
Country of Origin
Made in India
We are engaged in offering 410 Stainless Steel Plate to our clients. Our range of all products is widely appreciated by our clients.
Request Callback
Yes! I am Interested
Stainless Steel 329 Sheet
Get Best Quote
Approx. Price: Rs 500 / KgGet Latest Price
Product Details:
Thickness
5 mm
Technique
Hot Rolled
Color
Silver
Shape
Square
Product Brand
Milton Steel
Material
Stainless Steel
329 is a stainless, acid resistant, duplex steel with improved machinability. Since the steel is machinability improved, it is suitable for production of details with comprehensive machining
15 NB UP to 1200 NB IN SCH 5S, 10S ,10, 20, 40S, 40, STD, 60, 80S, 80, XS, 100, 120, 140, 160 & XXS.
15 NB UP to 100 NB IN 2000 LBS, 3000 LBS, 6000 LBS & 9000 LBS, 150 LBS, 250 LBS.
Specifications:
Form: Seamless & Welded Long Radius & Short Radius Elbow 90 Deg, Long Radius Elbow 45 Deg ,Long Radius & Short Radius Elbow 90 Deg, Long Radius Elbow 45 Deg, Long Radius & Short Radius Elbow 180 Deg ( Return Bend ), Reducing Elbow, Equal Tee, Un Equal Tee, Crosses, Concentric Reducer, Eccentric Reducer, Long Stubend, Short Stubend, Coller, Pipe Cap, Long Radius Bends R =3 D, 5 D, 6 D, 8 D ,10 D & 20 D In 15 Deg ,30 Deg, 60 Deg & 90 Deg And Drawing Bassed Butt Weld Fitting ( Customised ).
Inconel 625 is a high strength, highly corrosion resistant nickel-chromium-molybdenum alloy used in applications in the aerospace, oil and gas, automotive, marine, chemical processing and nuclear industries where strength at high temperature are required (between 1200° F - 1400° F)
Nickel is a silvery-white, hard, malleable, and ductile metal. It is a good conductor of heat and electricity. It is bivalent, that is it has a valency of two. The metal dissolves slowly in dilute acids
Inconel® 625 (AMS 5599, UNS N06625) is a nickel-based superalloy with excellent resistance to oxidation and corrosion. The nickel-chromium matrix of this material is reinforced by the addition of molybdenum and niobium, which is alloyed through solid solution strengthening
The Inconel 690 material is a kind of austenitic nickel-base superalloy, which has excellent stress corrosion cracking resistance, excellent corrosion resistance, high strength, strong antioxidation, and favorable metallurgy stability
Ferralium 255 is a super duplex stainless steel in the Ferralium family. It was the first super duplex stainless steel. Developed by Langley Alloys to meet the needs of the oil, gas and chemical industries, Ferralium 255 achieves higher strengths than most other stainless steel varieties and corrosion-resistant alloys.
A duplex is generally a property divided into two separate living units. Those units can be situated side by side or stacked one on top of the other (the “one-up, one-down”). There are separate entrances for each unit, and sometimes there are separate garages and yards, as well
Grade 431 stainless steels are martensitic, heat-treatable grades with excellent corrosion resistance, torque strength, high toughness and tensile properties. All these properties make them ideal for bolt and shaft applications. These steels, however, cannot be cold-worked owing to their high yield strength, hence they are suitable for operations such as spinning, deep drawing, bending or cold heading. Fabrication of martensitic steels is generally carried out using techniques that allow hardening and tempering treatments and poor weldability. The corrosion resistance properties of grade 431 steels are lower than that of austenitic grades. The operations of grade 431 are limited by their loss of strength at high temperatures, due to over-tempering, and loss of ductility at negative temperatures.
Key Properties:
The specified properties are for bar products in ASTM A276. The properties may not be necessarily similar to other forms such as forgings and plates.
Grade 431 stainless steels have considerable resistance to salt water, but they are less resistant to tropical water when compared to that of grade 316 steels. Grade 431 steels have overall corrosion resistance similar to, or slightly lower than, that of grade 304 steels.
Grade 431 steels with a smooth surface finish perform well in tempered and hardened conditions.
Heat Resistance:
Grade 431 steels are resistant to scaling at temperatures of 925°C in intermittent conditions, and 870°C during continuous operations. In general, these steels are not to be used at temperatures above standard tempering temperatures, owing to loss of mechanical properties.
Heat Treatment:
Full anneal — Full annealing cannot be performed on grade 431 steels. This grade gets hardened even during slow cooling.
Process anneal — Grade 431 steels are heated to 620 to 660°C and then air-cooled.
Grade 431 steels are generally hardened by heating at temperatures from 980 to 1065°C, holding for nearly ½ h, followed by oil or air quenching. Complex or hardened parts of grade 431 steels can be pre-heated to temperatures from 760 to 790°C and tempered, to improve their mechanical properties. Tempering of these steels at 425 to 600°C should be avoided, owing to the loss of impact toughness at this temperature range.
Welding:
Welding of grade 431 stainless steels is difficult due to the chances of cracking. It is recommended to pre-heat the materials to 200 - 300°C before welding, and carry out post-weld heat treatment at 650°C. Welding can be performed using grade 410 filler rods, but ductile welds can be achieved using grades 308L, 309 or 310 steels.
Machining:
Grade 431 steels can be easily machined in their annealed state. However, it is extremely difficult to machine these steels if they are hardened above 30HRC.
Applications:Typical applications of grade 431 stainless steels include the following:
Stainless steel is a corrosion-resistant alloy of iron, chromium and, in some cases, nickel and other metals. Completely and infinitely recyclable, stainless steel is the “green material” par excellence. In fact, within the construction sector, its actual recovery rate is close to 100%
Inconel 625® is a nonmagnetic, nickel-based alloy with a very broad operational temperature range (cryogenic to 2,000°F/1,093°C). Inconel 625® is known for its toughness, high fatigue strength, and oxidation resistance
Nickel sheet is a flat, uniformly sized piece of metal. Because of its characteristics including ferromagnetism, hardness, corrosion resistance, and electrical and thermal conductivity, nickel material is highly valuable when it is in sheet form. Nickel sheet also has excellent corrosion-resistant to aqueous alkali
A nickel sheet is a thin, flat metal shape with uniform thickness. Nickel sheets are made from bullets or ingots of pure nickel. They are also made from nickel alloys. Nickel sheets are thicker than foil while thinner than nickel plates, varying between 0.006 inches and 0.250 inches
Inconel 625® is a nonmagnetic, nickel-based alloy with a very broad operational temperature range (cryogenic to 2,000°F/1,093°C). Inconel 625® is known for its toughness, high fatigue strength, and oxidation resistance
A hard, shiny and strong metal. Titanium is as strong as steel but much less dense. It is therefore important as an alloying agent with many metals including aluminium, molybdenum and iron.
Hastelloy X is a solid-solution-strengthened nickel-chromium-iron-molybdenum alloy that combines good oxidation resistance, high-temperature strength and exceptional stress-corrosion resistance which makes this alloy also interesting for petrochemical applications.
Monel® is an alloy of nickel and copper that was first developed for commercial use in 1905. It is mainly used for its excellent corrosion and temperature resistance and is especially valued for applications in the marine and chemical processing industries
MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance. MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium
Nickel is a silvery-white, hard, malleable, and ductile metal. It is a good conductor of heat and electricity. It is bivalent, that is it has a valency of two. The metal dissolves slowly in dilute acids.
Hastelloy X is a solid-solution-strengthened nickel-chromium-iron-molybdenum alloy that combines good oxidation resistance, high-temperature strength and exceptional stress-corrosion resistance which makes this alloy also interesting for petrochemical applications
MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium. MONEL K500 retains the excellent corrosion resistant characteristics of 400 and has enhanced strength and hardness after precipitation hardening when compared with 400. Alloy K500 has approximately three (3) times the yield strength and double the tensile strength when compared with 400. MONEL K500 can be further strengthened by cold working before the precipitation hardening.
304 stainless steel plate has a minimum tensile strength of 75 ksi and a minimum yield strength at 0.2% of 30 ksi. 304 stainless steel plate has an elongation of 40%. This type of stainless steel plate has a maximum Brinell hardness of 201 and a Rockwell B hardness of 92. 304L stainless steel plate has a minimum tensile strength of 70 ksi and a yield strength at 0.2% of 25 ksi. This stainless steel plate also has an elongation of 40%, a maximum hardness of 201 on the Brinell scale and a hardness of 92 on the Rockwell B scale.
Grade 202 is chromium-manganese-nickel stainless steel with high toughness at low temperature. In comparison, grade 202 has less nickel content unlike 304. Hence it offers low corrosion resistance and lower toughness. But it is a less expensive substitution for grade 304 in many applications
Monel® is an alloy of nickel and copper that was first developed for commercial use in 1905. It is mainly used for its excellent corrosion and temperature resistance and is especially valued for applications in the marine and chemical processing industries
Titanium Grade 2 has good ductility, which allows for cold formability. To prevent cold forming concerns, the minimum bend radius for material under 0.070″ thick should be 2T, while 2.5T should be used for material over 0.070″. The material can also be easily machined, hot worked and welded.
